One of SAP’s unique strategic differentiations is embracing its partnership ecosystem and continuous willingness to support new platforms and technologies. This strategy can easily been seen in the...
The FlashArray Storage Replication Adapter for VMware Site Recovery Manager supports many:many replication since the 2.0 release of the SRA. Use of test failover, failover and reprotect is no different than with 1:1, and nor is the setup of the volumes. The only real difference is how you configure the array managers in SRM. So let’s review how this is done.
This is my configuration. One M20, one 405, and one 420:
So the first step is making sure that you have your arrays connected to one another. Here I have three arrays connected, this is as seen from my m20:
At this point you can move back to SRM. In my environment, my m20 is in my one site (let’s call it vCenter-1/SRM-1) and my 405 and my 420 is in my other site (let’s call it vCenter-2/SRM-2). So how do I build my array managers? So first I build my array manager in vCenter-1 that will be the source array manager for my m20.
Now choose single or pair. Either is fine. I am going to choose single to make the process a bit more clear for the purposes of explanation.
Now choose my vCenter-1.
Now add the information for the m20 into the local FlashArray entry:
Now, for the new part. Since this is a multi-array topology (in other words, this m20 is replicating volumes that need to be controlled by SRM to more than one target), you need to enter multiple targets into the peer entries in the array manager. Addresses must be entered in a comma separated fashion. So all target arrays into this array manager as a peer that the m20 (in my case) will be replicating to (and that you want SRM to control one of more of those replicated volumes). So, I will add my 405 and my 420.
Now finish the wizard. Do not enable any array pairs at this time, so skip this step and finish the wizard.
The array manager wizard will complete and the array manager will be created.
This next step we will need to run twice, once for the 405 and once for the 420. Now click to add a new array manager.
Once again, choose single array manager. This time, choose the opposing vCenter where you other arrays are. So for me, vCenter-2. This is important to choose the right vCenter, otherwise the steps afterwards will not work.
Choose the FlashArray SRA again and then move to the config screen. This time I will add an array manager for my 405. So I will add my 405 as the local FlashArray:
Then I can add my peers. I need to add any arrays back at the site 1 that I have volumes I am replicating to the 405 from, or from the 405 to. In this case, I only have my m20 at my first site. My 420 is not a source or a target of my 405 as it is also at my second site.
So I will just add my m20 as a peer.
This time, go ahead and enable the array pair for the m20 to the 405–it should already be checked.
Then finish the wizard. Now you have the 405 and m20 completed. Time to create the last array manager, the one for the 420.
Now create one last single array manager.
Choose the correct vCenter again. This time vCenter-2 just like the 405 as they are both in that site.
Choose the FlashArray SRA again and move to the config screen. Enter for the local FlashArray the information for the 420.
Now, just like the 405, I add the m20 as a peer FlashArray:
Now click next. You can now enable the 420-m20 array pair. It should already be checked, so leave it checked to enable it and then finish the wizard.
All of the array managers are added and enabled! Time to discover devices and create protection groups etc. Everything else is the same as before.
So some basic guidelines to make it easier to understand:
So let’s look a quick use case. I have the situation I configured above, but now I want to add another FlashArray (an m50) to my site 1 (vCenter-1/SRM-1) which is where my m20 is. I also want that to replicate to my 405 and my 420. What do I do?
Well I just need to do three things:
Create a new array manager on vCenter-1 that has my m50 as local and the 405 and 420 as peers:
We could technically enable the array pairs now, but issues could occur. We first should update the 405 and 420 array pairs to add the m50 as a peer. So skip enabling any pairs here. Deselect the pair if selected and finish.
Now edit the 405 array:
So add the m50 to the peer list, make sure to re-add credentials for the source and target, to authorize the change:
Now you can enable the m50 to 405 array pair. You will need to select this pair:
Repeat this process for the 420 array manager too.